WHAT IS A SILICONE RUBBER?

 

Silicone rubber is derived from inorganic silica (sand). Silicones were developed for commercial use during World War II to meet military applications requiring extreme temperature resistance.  Over the years, numerous advances were made to improve tensile strength, elongation and tear resistance as well as other improvements.  In addition to its broad temperature resistant properties silicone rubber now posses physical values superior to a number of other synthetic polymers.  Silicone rubber is made up of a backbone of silicone and oxygen atoms. This unique linkage is the same as that found in other high temperature materials such as quartz and glass.  As a result, silicone rubber provides outstanding high and low temperature resistant properties as well as general inertness toward many deteriorating factors such as ozone, corona, weathering, UV rays, acids, bases, salts, oils, fuels, fluids, and food products.

 

 

 

WHY USE IT?

 

PROTECTION:

·        RAIN DAMAGE

·        SALT DAMAGE

·        MOLE AND MILDEW

·        INSECTS

·        STAIN RESISTANT

SAFETY:

·        ENVIRONMENTAL

·        BIOLOGICAL

·        NON-HAZARDOUS

·        NON-TOXIC

·        NON-FLAMMABLE

 

DURABILITY:

·        UNAFFECTED BY EXTREME

·        TEMPERATURES (-70 to 400 F)

·        400% ELASTICITY

·        DOESN'T CRACK OR YELLOW

 

PREVENTS:

·        FREEZE, THAW, CRACKING, SPAWING

·         INSULATION ROBBED BY WATER INTRUSION

·        OXIDATION OF SURFACES AND MATERIALS FROM SUN/OZONE

·         RAPID DISCOLORATION OF FINE EXTERIOR WOODS SUCH AS CEDAR AND REDWOOD WHEN NATURAL LOOK IS DESIRED

PAINT ADDITIVE:

·        WITH OIL OR WATER BASED PAINTS

·        ELIMINATES NEED FOR PRIMER COAT WATER, INSECT, and RUST REPELLENT

COST:

·        MOST PROTECTON FOR INVESTMENT

 

20 YEARS MANUFACTURER WARRANTY

 

 

APPLICATION CONT.:

GENERAL APPLICATION INFORMATION: Water saturated surfaces may reduce penetration.  Damp substrates will increase cure time but will not harm the effectiveness of the sealer.  When utilizing a sprayer, spray to saturation level making sure all substrate has come in contact with the product.  Cover and protect all surfaces not to be treated (i.e. treat with soap and water.  If set up has occurred; clean equipment with mineral spirits or paint thinner.

 

ESTIMATED COVERAGE:

Coverage may vary from estimate due to variations in substrate and application techniques.

 

MATERIAL                            SQ.FT/GALLON

Concrete                                          200

Brick                                                  150

Stone                                                 200

Concrete Block                               150

Wood                                                 125

Cedar Shingles                               100

Stucco                                               175

Plastics                                             200

 

MATERIAL                            SQ.FT/GALLON

Cinder Block                                   150

Wood Decks                                    200

Aggregate                                        150

Asphalt                                             150

Canvas                                             200

Masonry                                           200

Metal Surfaces                               200

Leather/Vinyl                                  200

 

 

PAINT ADDITIVE:

HI-TEK SEALER can be mixed with any paint (Latex or any other water or oil based) or stain.  This enables the paint to take on the water proofing properties of the sealant without effecting quality and eliminates the need of a paint primer. Add one (1) cup per gallon of paint.  Coverage is the same as indicated by the paint supplier.

 

    

 

SPECIFICATION SHEET

 

(INCLUDES REGULAR, EXTRA STRENGTH AND SUPER CONCENTRATED)

 

 1.   PRODUCT NAME:

      HI-TEK SEALER      

                                         

 2.   PRODUCT DESCRIPTION:

Based Use: HI-TEK SEALER is a clear long lasting penetrating waterproofing sealer for use on variety of surfaces including wood, concrete, stucco, brick block, tile and canvas.  HI-TEK SEALER in a concentrate acts as an anti-graffiti barrier by filling voids in porous surfaces which minimizes the graffiti penetration, thus allowing for the graffiti removal with an approved cleaner and low pressure water spray.  HI-TEK SEALER increases the resistance to mold/mildew and reducing chemical and salt contact to the surface material.

 

Composition:  HI-TEK SEALER is a water-based one component liquid silicone rubber dispersion containing a proprietary blend of resins and penetrating agents that exhibits excellent water repellency and breathability.

Benefits: Ecologically safe, clear, penetrating film which does not discolor with ultraviolet rays.

                    •   Exceptional flexibility after curing, allowing for structural movement

                    •   Excellent water-repelling characteristics for long -term protection.

                    •   Extended resistance to mold and mildew.

                   •   Extensive gas permeability.

             Limitations:

                        •   Should be applied to clean and dry surfaces

            •   Adjacent areas and surfaces should be protected from contact with the sealant.

                        •   Should not be applied when inclement weather is imminent.

                       •   Should not be applied above 400F.

                        •   Should be applied where vapor barrier is required.             

                       •   Paint adhesion after application may be difficult unless paint contains silicone.

                       •   Care should be taken over substrates containing water soluble pigments.

                       •   A test area should always be done to verify compatibility of substrate with    product.

                       •   Excess material must always be removed from surface to prevent slipperiness.

•   Solvent-based products should not be applied over Hi-Tek Sealer.

 

3.  TECHNICAL DATA:

           Properties: See chart

           Coverage: See chart

 

COVERAGES	PER SQ.FT/GAL
Exterior Brick	125 – 150
Concrete	100 – 200
Stucco	80 – 175
Light	50 – 100
Dense Block	80 – 100
Stone	100 – 200
Wood	75 – 125

 

TYPICAL UNCURED PROPERTIES

 

Specific Gravity	1.0
PH.	7 – 8
Appearance	Milky – White
Solids by weight:
Regular	6-8%
Extra	12-14%
Super	18-20%
Concentrate	30-32%

 

TYPICAL CURED PROPERTIES

 

Initial Cure	1.5 hours
Final Cure	24 – 28 hrs depending on substrate and weather conditions.
Elongation (ASTMD 412)	325%
Water Vapor Transmission(ASTME96)	017 grains/hr/cu ft
Permeability	040 (Perm)
UV Resistance	Excellent

 

 

4.   INSTALLATION:

Preparation: Must include but not limited to:

•  All surfaces should be clean and free of loose materials, release oils and other

contaminants. These should be removed prior to application by power washing or appropriate cleaner. Cleaner must always be thoroughly rinsed from substrate prior to application of HI-TEK SEALER.

•  A test should always be done prior to application using the same cleaning and application procedures to be used on the project.

          Application:

                      •  Should be applied in accordance with specific application specifications.

                      •  Apply HI-TEK SEALER by low pressure spray unit, brush,  or roller.

                      •  Spray to saturation level with a minimum 1/4 inch rundown.  Excess material on surface should be removed

with a dry roller or cloth.  Damp substrates will increase the cure time. Do not apply when inclement weather is imminent. Immediately wash off any material on non-treated surfaces with a soap and water solution.

Cleaning:

   Clean all tools with soap and water.

 

 

 

BREMMER TEST RESULTS

 

What is the Bremmer Test?

The Bremmer test is designed to simulate a 60 mile per hour wind-   driven rain on the tested product as definite period of time.  Measurements are made of water penetration every 5 minutes up to a 12 hour period on untreated and treated products.  A comparison test is performed to determine the water sealant effectiveness of the sealant on the substrate being tested.

 

Product tested:

Large brick, small brick, and mortar joints.

 

Test results:

                                                                                                              

SURFACED TESTED	ELAPSED TIME	WATER PENETRATION
A.  Untreated Large Brick	20 minutes	½ Inch
	1 hour	1 Inch
	2 hour	2 ¾ inch
HI-TEK SEALER TREATED	1 HOUR	0
Large Brick	4 hours	0
	6 hours	1/8 Inch
	12 hours	¼ inch

 

B.  Untreated Small Brick	20 minutes	2/3 Inch
	1 hour	1 ¼ Inch
	2 hour	2 ¼ inch
HI-TEK SEALER TREATED	1 HOUR	0
Large Brick	4 hours	0
	6 hours	1/8 Inch
	12 hours	1/4 inch

 

C.  Untreated Mortar Joints	5 Minutes	1 Inch
HI-TEK SEALER TREATED	1 HOUR	0
	4 hours	0
	6 hours	1/8 Inch
	12 hours	1/4 inch

 

Based on the above test results Hi-Tek Sealer is an excellent solution to water penetration problems associated with brick and mortar joints.

 

 

 

ASTM TEST

 

Test Performed By:  United States Testing Company

 

TEST; Water Vapor Transmission Sate - ASTM METHOD £ 94-96 (Dry Desiccant)

 

SPECIFICATIONS OF TEST: Four (4) 12 inch by 12 inch panels of sheetrock were used for the test: One (1) panel was left untreated by HI-TEK SEALER.  Three (3) punches were treated with one (1) ounce or a 30% strength formula of Hi-Tek Sealer. This is five (5) times the normal application rate for masonry.  The coated panels were allowed to dry one (1) week then tested when dry to the touch.

 

RESULTS:                                              

 

Water Vapor Transmission                      Permeate

Panels Tested                       (Grains/Hr/Sq Ft)            (PERMS)

     Untreated                                2.267                           5.18

     Treated                                    2.360                           5.394

 

As shown by the test results, the coated and uncoated panels fail within the standard deviation of the test method. It can therefore be stated that Hi-Tek Sealer when applied at five (5) times the normal rate caused no measurable change in the Water Vapor Transmission Rate Permeate of the substrate it was applied to.

 

 

 

ASDTM TEST

 

TEST: Static Coefficient Of Friction:

ASTM Method C 1028 (Broadened to include Leather and Rubber-Sensor Pads)

ASTM Method D 2047

            ASTM Method E 303

 

SPECIFICATIONS OF TEST: Six (6) Gay Pavers were supplied to the testing company.  The pavers were scraped with paint scraper to remove the rough edges and all were wire brushed.  Three (3) of the Pavers were left untreated and 3 treated with Hi-Tek Sealer at a rate of 100 square feet per gallon and cured at room temperature.

 

RESULTS:   Water was applied to all six Pavers.  The three (3) uncoated Pavers all absorbed water.  The three (3) Hi-Tek Sealer Coated Pavers all were beaded with water and remain dry.  The Hi-Tek Sealer coated Pavers compared with the uncoated Pavers showed that the coated Pavers were well above the recognized satisfactory Coefficient of Friction Level of 0.05.